Introduction
Reline your sewer pipes with a special flexible hose insert and two-part resin. The new liner is essentially a flexible, rubberized tube made of polyester fabric that has been soaked in epoxy resin. To reline the pipe, you will install an inflatable bladder or ball inside the new liner, then insert it into the damaged sewer pipe and inflate it, pressing it against the walls of the old pipe. Once inflated, allow it to cure for four hours. After curing is complete, deflate the bladder and remove it from the newly lined pipe. How to fix a broken sewer pipe is always common ask questions by plumbers.
Finding a damaged sewer pipe
To locate the damaged section of pipe, you will need to use a sewer snake. A sewer snake is a long flexible metal rod that has sharp teeth on one end. The other end has a handle that allows you to maneuver it into the drain where it will find the blockage and dislodge it so that water can flow freely through your pipes again.
If you don’t have one already, here’s a link to buy one: https://www.amazon.com/gp/product/B0013Y5X9G/. You might also see them at home improvement stores or hardware stores near where you live.
Damaged or old sewer pipes can lead to serious problems.
Sewer pipes are usually hidden underground, making it difficult for homeowners to see whether or not their sewer lines are damaged. Because sewer lines are made of plastic, they can crack and break over time. They’re also buried underneath your home’s foundation, which makes repairs difficult.
Reline the damaged section of pipe rather than completely replacing the entire pipe.
If you have a section of your sewer pipe that is damaged, it is possible to replace the damaged section with a flexible liner. This can save you time and money by only replacing the section of pipe that needs fixing.
You may need to replace your entire sewer line if there are multiple sections that need repair and they do not line up with each other. In this case, it would be more cost effective to cut out all of your old pipes and start over with new ones rather than repairing each section as needed.
Reline the sewer pipe with a special flexible flexible hose insert and two-part resin.
To reline a sewer pipe, you’ll need to use a flexible hose insert. This is what will form the new pipe wall. You’ll also need two-part resin that’s mixed together and poured into the pipe, which cures to form a strong, flexible pipe liner. Once these materials are in place, you’ll be able to use your old sewage system for many years without worrying about clogs or other problems.
The new liner is essentially a flexible, rubberized tube made of polyester fabric that has been soaked in epoxy resin.
To make sure you are using the proper materials, your liner needs to be made of a flexible rubberized fabric that has been soaked in epoxy resin.
This type of material allows for easy installation and flexibility as it moves with your sewer pipes as they shift or settle.
To reline the pipe, you will install an inflatable bladder or ball inside the new liner, then insert it into the damaged sewer pipe and inflate it, pressing it against the walls of the old pipe.
To reline the pipe, you will install an inflatable bladder or ball inside the new liner, then insert it into the damaged sewer pipe and inflate it, pressing it against the walls of the old pipe.
Allow it to cure for four hours before deflating and removing it from your newly lined pipe.
Once inflated, allow it to cure for four hours.
You’ll need to allow the liner to cure for a minimum of four hours. The curing time will vary depending on several factors, including:
- Temperature: The temperature at which you cure your liner will determine how long it takes for the resin to harden and become permanent. Most manufacturers recommend that you cure your pipe insulator outdoors in direct sunlight, but some products can be cured indoors if necessary (this may result in slower curing time).
- Humidity levels: High humidity levels can slow down the curing process significantly; however, low humidity levels may not affect it at all.
- Type of resin used: Some liners use different types of resins than others do—for example, some are more resistant against UV light than others—and each type has its own unique set of curing specifications. This means that there isn’t necessarily just one set cure times for every product out there! Be sure to check with your local hardware store before attempting this project so they can provide you with a correct answer based off their specific brand’s instructions
After curing is complete, deflate the bladder and remove it from the newly lined pipe.
After curing is complete, deflate the bladder and remove it from the newly lined pipe. Using a sewer snake or a cable tool, remove any debris that may have gotten lodged in your newly lined pipeline. If you are unsure of how to use one of these tools, consult with someone who is familiar with them before attempting any work on your own.
After removing the liner from your pipes, clean up any mess created by removing it and make sure that all sharp objects have been removed from inside your pipe.
It’s not hard to reline your sewer pipes, but it does require some time and patience.
It’s not hard to reline your sewer pipes, but it does require some time and patience. First, you will need to gather the necessary tools:
- A power washer or streamer
- Disposable gloves (and perhaps a mask)
- Garden hose and nozzle (if using a water-based material)
Conclusion
Rerouting your sewer pipes is a great way to save money and keep your home safe from plumbing problems. It’s not a difficult process, but it does require some time and patience. Click here if you’re looking for help relining your pipe, contact us today!